Lancaster Electrical Company handles electrical repair and installation for homes, rental properties, and businesses throughout the Antelope Valley. From a dead outlet to a full panel replacement, we scope the job on the call, explain what it involves, and get it scheduled. We're available every day from 6:00 AM to 9:00 PM, so you don't have to wait until Monday to get a problem looked at.
Know the price. Know the scope. Know what happens next.
We keep your home powered and safe.
For residential and commercial electrical work alike, the range of what we handle is broad. Flickering lights, dead outlets, and tripping breakers are the calls we get most often, but we also run new wiring, install outlets and switches, hang ceiling fans, and set up indoor and outdoor lighting from one end of a property to the other.
Whether you own a single-family home, manage a multi-unit building, or run a commercial space, the work is done to the code inspectors in Lancaster enforce. That means the job is done once, done right, and ready to pass inspection when it needs to.
Dedicated circuits for major appliances, rewiring older rooms, and electrical safety inspections all fall within our scope as well. One call gets the problem looked at properly.
A flickering light and a full rewire start the same way: we find out what is actually happening before any work begins. Symptoms like lights that dim when an appliance kicks on, outlets that spark or feel warm to the touch, a burning smell near a switch plate, a buzzing panel, or a breaker that trips repeatedly all point to something that needs a closer look.
Half the house losing power at once often means a tripped double-pole breaker or a problem at the service entrance. An outlet that stopped working may be a tripped GFCI upstream, a loose connection, or a wiring fault. We trace the problem to its source and explain what we found before we start the repair.
An older panel is worth a look before a big appliance goes in. Lancaster has a mix of housing stock, and panels that were sized for a lighter load do not always keep up with modern demand. We check for overloaded circuits, outdated breakers, and wiring that no longer meets current standards. We're a straightforward choice for homeowners and property managers who want the fault explained before the work starts.
Don't let a small wiring issue turn into a fire risk. A panel that runs hot, trips frequently, or has no room for new circuits is not just an inconvenience. It is a sign that the electrical service may no longer match what the property needs.
We handle 100-amp to 200-amp upgrades, subpanel installations, and full service-entrance upgrades including meter work. A panel inspection will show whether the existing equipment can carry the current load or whether an upgrade makes more sense. When a kitchen remodel, an EV charger, or a new HVAC circuit is on the way, we run the load calculation first so the panel can handle what is being added.
The price is confirmed before we schedule anything. The wiring done properly, start to finish, is what we're here to deliver. We're one phone call from getting your power right.
The sooner you call, the sooner the power is back on, and that applies to installs just as much as repairs. A GFCI outlet in a kitchen or bathroom, an AFCI outlet in a bedroom circuit, a USB outlet at a desk or nightstand, a dimmer switch in a dining room: each of these is a straightforward job that makes a real difference in how a space works.
Ceiling fan wiring and installation, recessed LED lighting, under-cabinet lighting in a kitchen, outdoor security lights, motion sensor fixtures, and landscape lighting circuits all fall within what we install regularly. For commercial spaces, we handle lighting layouts for offices, retail floors, and common areas.
Every install starts with understanding what the space needs. We confirm the circuit capacity, place the fixture or device correctly, and leave the work clean. We keep your home powered and safe.
Running a refrigerator, dryer, washer, dishwasher, or microwave on a shared circuit is one of the more common causes of tripping breakers and nuisance faults. Each of those appliances draws enough current that it performs better and more safely on its own dedicated circuit.
We install dedicated circuits for all major appliances, including 240-volt outlets for dryers and ranges. Garage outlets, outdoor weatherproof outlets, and circuits that feed a disconnect for a cooling unit are all part of what we wire. When a new appliance is going in and the panel needs to accommodate the added load, we handle the circuit and the panel capacity together.
We take pride in the electrical work we leave behind. Every circuit is run cleanly, terminated correctly, and confirmed before we call the job done.
Older homes in the Lancaster area sometimes still carry knob-and-tube wiring or aluminum branch-circuit wiring, both of which present real risks when they are aging, modified incorrectly, or buried under insulation. Signs a home may need rewiring include frequently tripping breakers, outlets that feel warm, lights that flicker without an obvious cause, or a panel that shows signs of previous DIY work.
Knob-and-tube replacement involves running modern copper wiring through the existing wall cavities and connecting it to a properly sized panel. Aluminum wiring remediation typically involves installing approved connectors at every device and junction to reduce the risk of overheating at connections.
We also handle pre-purchase electrical inspections. If you are buying a home in Lancaster or Palmdale and want to know what the wiring looks like before you close, we walk through the panel, the visible wiring, and the outlets and report what we find. We're one phone call from getting your power right.
Lancaster sits in the Antelope Valley, where long sunny days and a growing population of electric vehicle owners have made solar, battery backup, and home EV charging a normal part of residential electrical work. Grid-stress events during peak summer demand add urgency to backup power planning. The three services below address what comes up most often here.
A Level 2 home EV charger runs on a dedicated 240-volt circuit and can fully charge most vehicles overnight, which matters in an area where commute distances are real and public charging is not always convenient. We start with a panel capacity check to confirm the existing service can support the added load, then run the circuit and install the outlet or hardwired unit in the garage or driveway location that works best for the vehicle. If the panel needs a circuit added or a breaker slot freed up, we handle that as part of the same job.
We work on the electrical side of solar and battery backup systems: wiring, transfer switches, and the panel upgrades needed to connect a solar array or battery bank to the home's electrical system. Lancaster's sun exposure makes rooftop solar one of the more cost-effective options in California, and the grid shutoffs that have affected the region during wildfire season have made battery backup a genuine priority for many households. We do not install the panels or the battery units themselves, but we make sure the electrical infrastructure is ready to support the system safely.
A whole-home surge protector installs at the main panel and catches voltage spikes before they reach the wiring and devices throughout the house. In Lancaster, where summer heat pushes grid load and air conditioning runs hard for months at a time, surges from utility switching and nearby lightning are a real concern. The installation involves mounting the device at the panel and connecting it to the grounding system. It protects everything downstream: appliances, electronics, HVAC equipment, and the wiring itself.
The sooner you call, the sooner the power is back on, and for landlords and property managers, a fast turnaround on electrical issues is not just a convenience. It is a code compliance matter. We handle outlet and lighting repairs, panel checks, GFCI and AFCI upgrades, and the kind of electrical work that comes up between tenants or during a unit renovation.
For commercial clients, we wire tenant improvements, run circuits for offices and retail floors, install lighting for restaurants and warehouses, and take on the electrical scope of small-business buildouts. The scope and the price are confirmed before anything is scheduled, so you know exactly what the work covers before it starts.
We're one phone call from getting your power right.
Kitchen and bathroom remodels almost always involve electrical work: new circuits for appliances, GFCI protection, updated lighting, and sometimes a panel upgrade to carry the added load. Home additions, garage conversions, and ADU builds require new wiring runs, dedicated circuits, and coordination with the rest of the electrical system.
For new construction, we handle the rough-in and finish work from the ground up. When a remodel is already underway, we schedule around the other trades and confirm the scope before the walls close. The electrical work done to the code inspectors here enforce means the inspection goes smoothly and the work does not have to be redone.
We keep your home powered and safe.
Plain answers. Clear options. Safe wiring.
When you call, we go through the job with you on the phone. What is happening, where it is happening, and what you have already noticed. From that, we give you a rate before anything is scheduled. The cost of a job depends on what it involves: the size of a panel upgrade, the number of circuits being added, the type of fixture going in, or the length of a wiring run. We explain what affects the price so you know what you are agreeing to.
The service call covers a proper look at the problem, not a quick visual from the doorway. We confirm what the job involves before the work starts, and if the scope changes once we are in the wall, we tell you before we continue.
One call gets the problem looked at properly.
Ready to get the power back on? Lancaster Electrical Company is available every day from 6:00 AM to 9:00 PM.
Call (661) 646-2995 to get a quote, schedule a service call, or ask what a job is likely to involve.
Know the price. Know the scope. Know what happens next.
A Level 2 EV charger requires a dedicated 240-volt circuit run from the panel to the charging location. Before that circuit is installed, we check whether the panel has enough available capacity to carry the added load without overloading the service. If the panel needs an upgrade or a breaker slot freed up, we scope that as part of the same job and confirm the full price before anything is scheduled.
If your home is adding a solar array or battery storage system and the panel has not been assessed, that is the first step. Signs the electrical side needs attention include a panel that is already near capacity, a service entrance that is not rated for the added load, or wiring that was not run with a future battery connection in mind. We handle the wiring, transfer switches, and panel upgrades on the electrical side without touching the panels or battery units themselves.
A panel that runs warm, hums or buzzes, trips breakers under normal load, or has no room for additional circuits is showing signs of strain. A fuse box that has never been replaced, or a panel that was sized for a much lighter electrical load than the property now draws, is worth having inspected before something fails. We assess the panel on the call and explain what the inspection involves before we schedule it.
A service upgrade replaces the existing panel and, where needed, the service entrance and meter connection with equipment sized for the property's actual electrical load. We run a load calculation before the upgrade is quoted so the new service is sized correctly. The work is done to the code inspectors here enforce, which means it is ready for inspection when required.
A whole-home surge protector installs at the main panel and intercepts voltage spikes before they reach the wiring and devices throughout the house. In Lancaster, where summer heat pushes grid demand and air conditioning runs hard for months, surges from utility switching and nearby lightning are a genuine concern. The installation involves connecting the device to the panel's grounding system, and we confirm that grounding and bonding are correct before we leave.
We start with a diagnostic to identify the root cause of the problem, not just the visible symptom. Once we know what is happening, we explain the fault and confirm the repair before any work begins. If the scope changes once we are in the wall or behind the panel, we tell you before we continue.
A quick repair addresses a specific fault: a failed outlet, a loose connection, a tripped GFCI that will not reset. A rewire addresses the wiring itself across a room, a floor, or the whole house, typically because the existing wiring is too old, the wrong material, or no longer meets current code. We determine which one applies after the diagnostic, and we explain the difference before any work is priced or scheduled.
A full or partial rewire is typically needed when the existing wiring is knob-and-tube, aluminum branch-circuit wiring, or wiring that has been modified incorrectly over the years. Frequently tripping breakers, warm outlets, lights that flicker without a clear cause, or a panel showing signs of DIY work are all reasons to start with an inspection. The inspection tells you what is in the walls before any rewiring is planned or priced.
Yes. Adding GFCI outlets in kitchens, bathrooms, garages, and outdoor locations is a code requirement in those areas regardless of when the home was built, and it is work we do regularly. Where the existing wiring is ungrounded, we explain the options for bringing those circuits up to current standards before any work is scheduled.
GFCI protection is required in kitchens, bathrooms, garages, outdoor locations, and anywhere near water. AFCI protection is required in bedrooms and, under current code, in most living areas of a home. Where those protections are missing in an older home, we identify the affected circuits during an inspection and explain what it takes to bring them up to standard.
We serve Lancaster and the communities around it throughout the Antelope Valley and the northern reaches of Los Angeles County, including Palmdale, Quartz Hill, Lake Los Angeles, Littlerock, Pearblossom, Acton, Hi Vista, and Rosamond. If you are outside Lancaster and not sure whether we cover your address, call and ask.
Below is a quick look at the electrical work we handle for homes, rental properties, and businesses throughout the Antelope Valley. Each service starts the same way: a call where we go through what is happening, confirm the scope, and give you a price before anything is scheduled. Whether the job is a single outlet or a full panel upgrade, we explain what it involves and what you can expect.
| Electrical Service | What the Job Involves | When You Need It | Things to Know |
|---|---|---|---|
| Older-Home Rewiring | Knob-and-tube replacement, Aluminum wiring remediation, Pre-purchase electrical inspection, Panel and wiring assessment | Older Lancaster properties with original wiring or signs of previous DIY electrical work | Flickering lights and warm outlets are warning signs, not quirks. We trace the issue to the wiring before any rewire is planned or priced. |
| Outlet and Switch Installation | GFCI and AFCI outlets, USB and standard outlets, Dimmer switches, Dedicated outlet placement | Kitchens, bathrooms, garages, and outdoor areas that need code-compliant protection | GFCI protection is required in kitchens, bathrooms, garages, and outdoor locations regardless of when the home was built. |
| Whole-Home Surge Protection | Panel-mounted surge device, Grounding and bonding check, Protection for appliances and electronics, HVAC and wiring coverage | Homes in Lancaster where summer grid demand and heat-driven surges are a seasonal concern | A whole-home surge protector catches voltage spikes before they reach the wiring and devices throughout the house. |
| Breaker and Fuse Repair | Breaker replacement, Fuse box evaluation, Double-pole breaker faults, Nuisance trip diagnosis | Homes where a breaker trips under normal load or will not hold a reset | A breaker that trips repeatedly under normal use often points to a wiring fault or an overloaded circuit, not just a weak breaker. |
| Ceiling Fan Installation | New fan and wiring installation, Fan-rated box replacement, Switch and remote wiring, Existing fixture swap | Rooms without a ceiling fan circuit or homes replacing an older fixture | A fan-rated ceiling box is required for safe installation. We confirm the box before the fan goes up. |
| EV Charger Installation | Dedicated 240-volt circuit, Panel capacity check, Hardwired or outlet-style charger, Garage and driveway placement | Lancaster and Antelope Valley homeowners with an electric vehicle and a long daily commute | An EV charger or a hot tub often means checking the panel first. We handle the circuit and any panel work as part of the same job. |
| Dedicated Appliance Circuits | 240-volt dryer and range outlets, Refrigerator and dishwasher circuits, Garage and workshop circuits, Disconnect wiring for cooling units | Kitchens, laundry rooms, and garages where a shared circuit causes repeated tripping | Running a dryer or range on a shared circuit is one of the more common causes of nuisance faults and breaker wear. |
| Electrical Repairs and Troubleshooting | Dead outlets and switches, Tripping breakers, Flickering or dimming lights, Fault tracing before any repair | Any home or business with an unexplained electrical symptom | Warm outlets, buzzing panels, and lights that dim when an appliance kicks on are warning signs worth acting on promptly. |
| Wiring and Circuit Installation | New circuit runs, Rewiring older rooms, Garage and outdoor circuits, Pre-purchase electrical inspections | Additions, garage conversions, ADU builds, and homes with aging or modified wiring | We confirm circuit capacity and panel availability before any wiring run is priced or scheduled. |
| Lighting Installation | Recessed LED and under-cabinet lighting, Outdoor security and motion fixtures, Landscape lighting circuits, Commercial lighting layouts | Remodels, new construction, and commercial spaces updating their lighting | Outdoor fixtures in Lancaster handle significant UV and heat exposure, so placement and circuit protection both matter. |
| Electrical Panel and Service UpgradesMost Popular | 100-amp to 200-amp upgrades, Subpanel installation, Service entrance and meter work, Load calculation before upgrade | Homes adding EV chargers, major appliances, or a remodel that pushes the existing panel past its limit | Panel work is permitted and inspected to the code inspectors here enforce, so the upgrade is ready to pass inspection when required. |
| Electrical Safety Inspections | Panel and breaker review, Outlet and switch condition check, Visible wiring assessment, Written findings after the visit | Buyers, landlords, and property managers who want to know what the electrical system looks like before committing | An inspection scopes the panel, the visible wiring, and the outlets and reports what we find before any repair is discussed. |
| Solar and Battery Backup Wiring | Transfer switch installation, Panel upgrades for solar connection, Battery bank wiring, Service entrance readiness | Lancaster homes adding solar or battery storage and needing the electrical infrastructure to support it | We work on the electrical side only. We do not install panels or battery units, but we make sure the wiring and panel are ready for the system. |
What causes a breaker to trip repeatedly and when does it point to a wiring problem?
A breaker that trips under normal load is telling you something. It may be a circuit carrying more devices than it was sized for, a loose or corroded connection generating heat, or a wiring fault somewhere along the run. Resetting the breaker addresses the symptom, not the cause. We trace the fault to its source and explain what we found before any repair is quoted or started.
Is electrical work in Lancaster permitted and inspected?
Panel upgrades, new circuit runs, and rewiring work are typically subject to permit and inspection requirements. The specifics depend on the scope of the job and whether it touches the service entrance. We confirm what applies to your job before we schedule it, and the work is done to the code inspectors here enforce so it is ready to pass inspection when required.
What are the risks of aluminum branch-circuit wiring in an older home?
Aluminum wiring expands and contracts more than copper under load, which can loosen connections at outlets, switches, and junction points over time. Loose connections generate heat, and heat at a connection is a fire risk. Remediation typically involves installing approved connectors at every device and junction. We inspect the wiring and explain the condition before any work is priced.
Faults Traced Before Anything Is Replaced
We identify the root cause of the problem before any repair is quoted or started. If the scope changes once we are in the wall or behind the panel, we tell you before we continue.
Do I need to be home while the electrical work is being done?
For most jobs, yes. Access to the panel, the affected circuits, and the work area is needed throughout the visit. We confirm the scope and timing on the call so you can plan around it. If a job requires a return visit, we schedule that before we leave.
How does pricing work and when do I get a number?
We go through the job with you on the phone: what is happening, where it is happening, and what you have already noticed. From that conversation we give you a rate before anything is scheduled. The cost depends on what the job involves, whether that is the size of a panel upgrade, the number of circuits being added, or the length of a wiring run. We explain what affects the price so you know what you are agreeing to.
When should I call an electrician instead of trying to fix something myself?
If the problem involves the panel, the wiring inside a wall, a breaker that will not hold, an outlet that feels warm, or anything that involves the service entrance, call us. Replacing a burned-out bulb or resetting a tripped GFCI is straightforward. Anything beyond that, especially in a home with older wiring, carries a real risk of making the underlying fault worse or creating a new one.
Code-Compliant Work on Every Job
Every job is done to the code inspectors here enforce. Panel upgrades, new circuits, and rewiring work are ready for inspection when required, without a return visit to correct what was missed.
What do flickering or dimming lights usually mean?
Lights that flicker when a large appliance kicks on often point to a voltage drop on an overloaded circuit or a loose neutral connection. Lights that dim throughout the house at once can indicate a problem at the service entrance or a failing utility connection. Either symptom is worth having traced. We find the source and explain what it is before any repair is started.
What is involved in adding circuits for a workshop or garage?
A garage or workshop circuit starts with a load calculation to determine what the space needs: the number of outlets, whether 240-volt power is required for tools or equipment, and whether the existing panel has the capacity to support the added load. We run the circuit from the panel, install the appropriate outlets, and confirm everything is correctly protected before we close up.
Scope Agreed Before the Panel Is Opened
We confirm what the job involves and give you a price before any work begins. If the situation in the wall turns out to be different from what the symptoms suggested, we explain it and get your agreement before we go further.
How long does a panel upgrade or rewire typically take?
A panel upgrade is usually a one-day job, though service entrance work and coordination with the utility can extend that timeline. A partial rewire covering one or two rooms typically takes a day or two depending on access. A full-home rewire takes longer and is scoped carefully before any work begins. We give you a realistic timeframe on the call before anything is scheduled.
Is my home ready for the electrical load a new appliance or EV charger adds?
That depends on the current state of the panel and the service entrance. A panel that is already near capacity may not have room for a new 240-volt circuit without an upgrade. We run a load calculation before any new circuit is quoted so you know whether the panel can carry the added load or whether an upgrade makes more sense first.
What is grounding and bonding, and why does it matter in an older home?
Grounding gives fault current a safe path back to the source so a breaker can trip and clear the fault. Bonding ties metal components together so they stay at the same electrical potential. In older homes, grounding may be absent on two-prong outlets or improperly done on added circuits. We check grounding and bonding as part of any inspection and explain what we find before any work is planned.
Call (661) 646-2995 to go through the job, get a price, and find out what the work involves before anything is scheduled.
(661) 646-2995